Hi,
None of the Secureplatforms seem to detect this card. This is a Broadcom
5703 CKHB NIC that is built-in Compaq DL360 G3. I used FP2 and FP3.
[Expert@cpmodule]# insmod bcm5700
Using /lib/modules/2.4.9-34cp/kernel/drivers/addon/bcm5700/bcm5700.o
/lib/modules/2.4.9-34cp/kernel/drivers/addon/bcm5700/bcm5700.o: init_module:
No such device
Hint: insmod errors can be caused by incorrect module parameters, including
invalid IO or IRQ parameters
#lspci -v
01:02.0 Ethernet controller: BROADCOM Corporation: Unknown device 16a7 (rev
02)
Subsystem: Compaq Computer Corporation: Unknown device 00cb
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at f7af0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
04:02.0 Ethernet controller: BROADCOM Corporation: Unknown device 16a7 (rev
02)
Subsystem: Compaq Computer Corporation: Unknown device 00cb
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at f7bf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
I got src rpm from HP site but compiling a new kernel on Secureplatform
seems next to impossible. I had a tough time sourcing the kernel-2.4.9-33/34
but the other dozen dependancies seem difficult to get around.
Regards,
Siddhartha
-----Original Message-----
From: Frank Darden [mailto:fdarden AT LOCKED DOT COM]
Sent: Wednesday, May 28, 2003 7:07 PM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: [FW-1] RE: [FW-1] RE: [FW-1] Réf. : Re: [FW-1] Secureplatform
on HP DL360 with Broadcom NIC
We have had nothing but great success using the Compaq DL series platforms
with SecurePlatform. We have many clients in production in this manner, and
by far seems to be the most reliable hardware for SecurePlatform. I cant
comment on the Broadcom NICS, but I do know that the stock Compaq FE/GE
cards work well.
-----Original Message-----
From: Wilger, Doug [mailto:Doug.Wilger AT HP DOT COM]
Sent: Wednesday, May 28, 2003 10:44 AM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: [FW-1] RE: [FW-1] Réf. : Re: [FW-1] Secureplatform on HP DL360 with
Broadcom NIC
Basically, because the autoconfig didn't properly set up the NIC (speed was
right, duplex was wrong), we couldn't reliably communicate with the
firewall, dropped connections, etc. The firewall was useless until we got
the local site tech to redo the NIC configuration so that we could
communicate with the box.
I haven't seen any kernel PANICs on any of the ones I've been working with
(3 DL360's, 2 DL380's, 1 DL320 so far) at my current client.
Doug
-----Original Message-----
From: noel.breton AT CNAV DOT FR [mailto:noel.breton AT CNAV DOT FR]
Sent: Wednesday, May 28, 2003 3:36 AM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: [FW-1] Réf. : Re: [FW-1] Secureplatform on HP DL360 with Broadcom
NIC
Hi,
What kind of major issue did you have ?
We have the same configuration except that whe have in addition some Dual
Intel Pro 100 ethernet cards. When some FTP flow go through the FW, the
system PANIC with an KERNEL error.
Bye.
Noël BRETON
Caisse Nationale d'Assurance Vieillesse
15, avenue Louis Jouhanneau
BP 7266
37072 TOURS CEDEX 02
Tél : +33 (0)2 47 88 73 86
Fax : +33 (0)2 47 88 75 84
Email : noel.breton AT cnav DOT fr
|---------+-------------------------------------------->
| | "Wilger, Doug" |
| | <Doug.Wilger AT HP DOT COM> |
| | Envoyé par : Mailing list for |
| | discussion of Firewall-1 |
| | <FW-1-MAILINGLIST AT AMADEUS.US DOT CHEC|
| | KPOINT.COM> |
| | |
| | |
| | 27/05/2003 16:45 |
| | Veuillez répondre à Mailing list |
| | for discussion of Firewall-1 |
| | |
|---------+-------------------------------------------->
>---------------------------------------------------------------------------
-------------------|
|
|
| Pour : FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
|
| cc :
|
| Objet : Re: [FW-1] Secureplatform on HP DL360 with Broadcom NIC
|
>---------------------------------------------------------------------------
-------------------|
Yes, several of them in fact. Note that in some cases you need to hardcode
the speed of the NIC's, - I had problems with one box not properly
autonegotiating which caused major issues.
Add a line after "alias eth0..." in /etc/modules.conf:
options bcm5700 line_speed=xx full_duplex=yy
Replace xx with the speed (10,100,1000)
Replace yy with 1 for full duplex or 0 for half duplex
For more than 1 NIC (obviously there will be at least 2), add the parameters
as a comma separated list
Ex: options bcm5700 line_speed=100,10 full_duplex=1,0 will set eth0 to 100
Mb/FDX, eth1 to 10 Mbit/HDX, assuming eth0 and eth1 are the Broadcom NIC's
Doug
-----Original Message-----
From: Siddhartha Jain(IT) [mailto:SiddharthaJ AT BANKMUSCAT DOT COM]
Sent: Tuesday, May 27, 2003 1:47 AM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: [FW-1] Secureplatform on HP DL360 with Broadcom NIC
Hi,
Has anyone got Secureplatform (any version) working on HP/Compaq DL 360 G3
with Broadcom 5700 Gigabit NICs?
TIA,
Siddhartha
"This email message is intended for the named recipient only. It may be
privileged and/or confidential. If you are not the intended named recipient
of this email then you should not copy it or use it for any purpose, nor
disclose its contents to any other person which is strictly prohibited and
unlawful"
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
"This email message is intended for the named recipient only. It may be
privileged and/or confidential. If you are not the intended named recipient
of this email then you should not copy it or use it for any purpose, nor
disclose its contents to any other person which is strictly prohibited and
unlawful"
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
|
