I recently installed Secure Platform on a new DL360 G2 I believe. It auto
detected everything! I didnt have to do anything but modify the
modules.conf file to tell it to come up at 100Mb/Full Duplex. I would
assume that the G3 is the same...
I just have a defualt install. I havent done anything other than install
and license.
Here is my output:
01:05.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5701
Gigabit Ethernet (rev 15)
Subsystem: Compaq Computer Corporation NC7780 1000BaseTX
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 5
Memory at f7fb0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable
-
01:06.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5701
Gigabit Ethernet (rev 15)
Subsystem: Compaq Computer Corporation NC7780 1000BaseTX
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 10
Memory at f7fa0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable
lsmod in case there are dependencies that you are missing:
Module Size Used by Tainted: PF
vpnmod.2.4.x 738016 2
fwmod.2.4.x 2023584 7
simmod.2.4.x 391296 0
bcm5700 64452 2
md 63744 0 (unused)
usb-ohci 19744 0 (unused)
usbcore 51072 1 [usb-ohci]
ext3 60544 5
jbd 40324 5 [ext3]
cciss 38368 6
sd_mod 11740 0 (unused)
scsi_mod 96344 1 [cciss sd_mod]
IT said:
> Hi,
>
> None of the Secureplatforms seem to detect this card. This is a Broadcom
> 5703 CKHB NIC that is built-in Compaq DL360 G3. I used FP2 and FP3.
>
> [Expert@cpmodule]# insmod bcm5700
> Using /lib/modules/2.4.9-34cp/kernel/drivers/addon/bcm5700/bcm5700.o
> /lib/modules/2.4.9-34cp/kernel/drivers/addon/bcm5700/bcm5700.o:
> init_module: No such device
> Hint: insmod errors can be caused by incorrect module parameters,
> including invalid IO or IRQ parameters
>
<--SNIP-->
> I got src rpm from HP site but compiling a new kernel on Secureplatform
> seems next to impossible. I had a tough time sourcing the
> kernel-2.4.9-33/34 but the other dozen dependancies seem difficult to
> get around.
<--SNIP-->
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
|
