Hi,
The difference between G2 and G3 is the Broadcom NIC. G2s seem to come with
BCM 5701 while the G3 comes with BCM 5703. We hadn't been touching FP4 coz
its Early deployment release or whatever its called in Checkpoint world. :)
But looks like we might have to get it now.
Thanks for all inputs.
Regards,
Siddhartha
-----Original Message-----
From: Caleb Walker [mailto:cp AT cwalk DOT org]
Sent: Thursday, May 29, 2003 1:46 AM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Cc: SiddharthaJ AT BANKMUSCAT DOT COM
Subject: Re: [FW-1] Secureplatform on HP DL360 with Broadcom NIC
I recently installed Secure Platform on a new DL360 G2 I believe. It auto
detected everything! I didnt have to do anything but modify the
modules.conf file to tell it to come up at 100Mb/Full Duplex. I would
assume that the G3 is the same...
I just have a defualt install. I havent done anything other than install
and license.
Here is my output:
01:05.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5701
Gigabit Ethernet (rev 15)
Subsystem: Compaq Computer Corporation NC7780 1000BaseTX
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 5
Memory at f7fb0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable
-
01:06.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5701
Gigabit Ethernet (rev 15)
Subsystem: Compaq Computer Corporation NC7780 1000BaseTX
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 10
Memory at f7fa0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable
lsmod in case there are dependencies that you are missing:
Module Size Used by Tainted: PF
vpnmod.2.4.x 738016 2
fwmod.2.4.x 2023584 7
simmod.2.4.x 391296 0
bcm5700 64452 2
md 63744 0 (unused)
usb-ohci 19744 0 (unused)
usbcore 51072 1 [usb-ohci]
ext3 60544 5
jbd 40324 5 [ext3]
cciss 38368 6
sd_mod 11740 0 (unused)
scsi_mod 96344 1 [cciss sd_mod]
IT said:
> Hi,
>
> None of the Secureplatforms seem to detect this card. This is a Broadcom
> 5703 CKHB NIC that is built-in Compaq DL360 G3. I used FP2 and FP3.
>
> [Expert@cpmodule]# insmod bcm5700
> Using /lib/modules/2.4.9-34cp/kernel/drivers/addon/bcm5700/bcm5700.o
> /lib/modules/2.4.9-34cp/kernel/drivers/addon/bcm5700/bcm5700.o:
> init_module: No such device
> Hint: insmod errors can be caused by incorrect module parameters,
> including invalid IO or IRQ parameters
>
<--SNIP-->
> I got src rpm from HP site but compiling a new kernel on Secureplatform
> seems next to impossible. I had a tough time sourcing the
> kernel-2.4.9-33/34 but the other dozen dependancies seem difficult to
> get around.
<--SNIP-->
"This email message is intended for the named recipient only. It may be
privileged and/or confidential. If you are not the intended named recipient
of this email then you should not copy it or use it for any purpose, nor
disclose its contents to any other person which is strictly prohibited and
unlawful"
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
|
