Not supported and some things might even just NOT WORK, at least that's what I
saw with RH8.
Regards,
Werner
-----Original Message-----
From: Mailing list for discussion of Firewall-1 [mailto:FW-1-MAILINGLIST AT
AMADEUS.US.CHECKPOINT DOT COM] On Behalf Of José María Gabaldón
Sent: Tuesday, August 31, 2004 18:07
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: Re: [FW-1] Linux Install
Hi,
Eventhough you could install FW-1 on Linux 9, it is NOT supported. FW-1 is only
supported on RH 7.2 and 7.3. Why don't you try SPLAT?
Cheers,
_______________________________
Cybertech Projects
José María Gabaldón
Network Security Engineer
email: jgabaldon AT cybertech.com DOT ve
www.cybertech.com.ve
-----Mensaje original-----
De: Mailing list for discussion of Firewall-1 [mailto:FW-1-MAILINGLIST AT
AMADEUS.US.CHECKPOINT DOT COM] En nombre de Lyle Dove Enviado el: Martes, 31 de
Agosto de 2004 10:32 a.m.
Para: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Asunto: [FW-1] Linux Install
Hello,
I am setting up to migrate my installation to a Red hat Linux v9.0 platform. I
was able install everything as expected, the OS, FW-1/VPN-1, etc.. I was able
to connect to the FW with the GUI application, setup a subset of rules to test
with, etc. The configuration of the machine is 3 network interfaces. My
external WAN interface, and 2 internal, 1 LAN, 1 DMZ. I am attempting to
connect a device in the DMZ to start with to test. I was able to successfully
ping the PC to the FW itself, but can't ping from the PC to the FW, or anything
past it. From the FW, I can access everything as expected out to the internet,
and anything connected to either the LAN or DMZ interfaces. Below is the route
output from the Linux box. I've x'ed out the WAN interface IP for obvious
reasons, but I'm not sure what the problem is. In comparison to my previous
setup, a Nokia IP380, it appears to be configured the same. With the Nokia, I
didn't have to do any static route configuration like !
it appears I have to do on the Red hat box. Can someone confirm this, or point
me in the right direction?
[root@wp-bpsfw bin]# route -nv
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
x.x.x.0 0.0.0.0 255.255.255.192 U 0 0 0
eth0
192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0
eth2
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0
eth1
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0
lo
0.0.0.0 x.x.x.1 0.0.0.0 UG 0 0 0
eth0
[root@wp-bpsfw bin]#
x.x.x.0 is the subnet of my WAN interface, and x.x.x.1 is the eth0 IP address.
Thanks!
--------
Beep! Beep!
Lyle Dove
BPS Senior Technician
Time Warner Cable - Los Angeles Division
"The information transmitted is intended only for the person or entity to which
it is addressed and may contain confidential, proprietary, and/or privileged
material. Any review, retransmission, dissemination or other use of, or taking
of any action in reliance upon, this information by persons or entities other
than the intended recipient is prohibited. If you received this in error,
please contact the sender and delete the material from all computers."
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail =================================================
To unsubscribe from this mailing list,
please see the instructions at http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail =================================================
To unsubscribe from this mailing list,
please see the instructions at http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
|
