Very odd. I've been using hide NAT since the day it was installed, and no
problems. Keep in mind that these 2 networks are internal networks in which
the firewall is basically acting as a router between the two. No other
routed segments exist behind each interface other than the single segment
defined on the FW.
Thoughts?
-Lyle
-----Original Message-----
From: Mailing list for discussion of Firewall-1
[mailto:FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM] On Behalf Of Joao
Santos
Sent: Friday, November 19, 2004 7:59 AM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: Re: [FW-1] Disconnected network shares
Hi Lyle! I had this same problem, same config... I was using hiding NAT for
the other network. I had to use static nat to fix the problem.
Hope this helps.
João.
On Fri, 19 Nov 2004 07:16:20 -0800, Lyle Dove <ldove AT bizla.rr DOT com> wrote:
> Hello,
>
> I have the following configuration
>
> Nokia IP380, IPSO 3.5.1, NG-AI FP3
>
> We have a MS network in which we have mapped drives which traverse
> through the FW from one network to another. The problem is that after a
short
> period of time, the shares/mapped drives appear to timeout. Once we
> attempt to access the shares/drives again, it takes a few seconds for
> them to 're-sync' and then everything works fine again. If we go to
> the same network segment, and then map the drives, they work as
> expected, and don't timeout. Is there something in the FW
> configuration that I can check that may cause this?
>
> Thanks,
>
> --------
> Beep! Beep!
>
> Lyle Dove
> BPS Senior Technician
> Time Warner Cable - Los Angeles Division
>
> "The information transmitted is intended only for the person or entity
> to which it is addressed and may contain confidential, proprietary,
> and/or privileged material. Any review, retransmission, dissemination
> or other use of, or taking of any action in reliance upon, this
> information by persons or entities other than the intended recipient
> is prohibited. If you received this in error, please contact the
> sender and delete the material from all computers."
>
> =================================================
> To set vacation, Out-Of-Office, or away messages, send an email to
> LISTSERV AT amadeus.us.checkpoint DOT com
> in the BODY of the email add:
> set fw-1-mailinglist nomail
> =================================================
> To unsubscribe from this mailing list, please see the instructions at
> http://www.checkpoint.com/services/mailing.html
> =================================================
> If you have any questions on how to change your subscription options,
> email fw-1-owner AT ts.checkpoint DOT com
> =================================================
>
=================================================
To set vacation, Out-Of-Office, or away messages, send an email to
LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
|
