Classification: UNCLASSIFIED
Caveats: NONE
I've tried it with one disk in a RAID 0 configuration and it blows up before
the format begins and says something about Fatal error on sda17
JIMMY DEARING
Infrastructure Analyst
Contractor (Electronic Data Systems)
(314) 592-0000 ext 3724
OFFICE: (314) 592-0505
FAX (314) 592-0526
EMAIL: jimmy.wayne.dearing AT us.army DOT mil
-----Original Message-----
From: Mailing list for discussion of Firewall-1
[mailto:FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM] On Behalf Of Ramki
Security
Sent: Tuesday, May 23, 2006 11:55 AM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: Re: [FW-1] Installing SPLAT on Dell PowerEdge 2850 (UNCLASSIFIED)
I had done the same install on R60 HFA3 on the same hardware but without
the additional harddisks you have. It went through fine. May be you
want to put only one HDD in its default configuration and try installing
again to see it that helps.
Ramki
CCNA, CCSE-NGAI
Dearing, Jimmy (EDS Contractor) wrote:
> Classification: UNCLASSIFIED
> Caveats: NONE
>
> Ive been attempting to install SPLAT on a Dell PowerEdge 2850 Server that
> has dual 3.8ghz processors with 2mb L2 Cache, 12gb RAM, Dual Embedded
Intel
> Gigabit1 82541 Server Adapter, PERC 4e/Di controller. It has six 15,000rpm
> 146gb hard drives that are setup as follows:
>
>
>
> On Channel 0 of the PERC controller there are two disks, setup in a RAID 1
> (mirror)
>
>
>
> On Channel 1 of the PERC controller there are 4 disks, setup in a RAID 5.
>
>
>
> The SPLAT install says all hardware is compatible and it goes into the
> install. Once it begins formatting the /opt partition, it seems to hang.
> I_ve tried it three different times and it has currently been setting at
the
> formatting /opt screen for 24 hours.
>
>
>
> Ive tried this on two different identical 2850_s with both giving the
same
> results.
>
>
>
> Am I missing something here? Can anyone see something wrong with my
hardware
> setup?
>
>
>
>
>
>
>
>
>
> Classification: UNCLASSIFIED
> Caveats: NONE
>
>
> =================================================
> To set vacation, Out-Of-Office, or away messages,
> send an email to LISTSERV AT amadeus.us.checkpoint DOT com
> in the BODY of the email add:
> set fw-1-mailinglist nomail
> =================================================
> To unsubscribe from this mailing list,
> please see the instructions at
> http://www.checkpoint.com/services/mailing.html
> =================================================
> If you have any questions on how to change your
> subscription options, email
> fw-1-owner AT ts.checkpoint DOT com
> =================================================
>
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
Classification: UNCLASSIFIED
Caveats: NONE
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
|
