Hi Clive,
Broadcast/Multicast: This differentiates how the cluster members
communicate with each other. Multicast would required special
configuration in some switches connecting the cluster members and hence
may create issues. Broadcast would eliminate this issue.
Ramki
CCNA, CCSE-NGAI
Clive Luk wrote:
Thanks for you quick reply Ramki,
I am new to checkpoint. Do you think you can give me some direction on
setting up my v240 as a HA cluster?
Actually I have a few questions want to ask.
What is the different between broadcast mode and multicast mode?
Does that require an extra license to setup HA/LS cluster?
Do you use cross over cable to sync. the state?
Cheers,
Clive
-----Original Message-----
From: Mailing list for discussion of Firewall-1
[mailto:FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM] On Behalf Of Ramki
Security
Sent: Thursday, 13 July 2006 1:26 PM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: Re: [FW-1] Solaris 9 BGE card and NGX60
Yes. My setup is active/standby cluster (not loadsharing) in new mode.
There is no VLAN involved. Both cluster members are V240 servers on
Solaris 9. Using broadcast mode instead of multicast.
Ramki
CCNA, CCSE-NGAI
Clive Luk wrote:
Hi Ramki,
Thanks for your reply. I have done some research on the net and
SecureKnowledge. It seems it will not work with Cluster and VLAN. Because
I
have got two V240 wanted to setup a Cluster.
Just a question have you got your V240 working with Cluster?
Cheers,
Clive
-----Original Message-----
From: Mailing list for discussion of Firewall-1
[mailto:FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM] On Behalf Of Ramki
Security
Sent: Thursday, 13 July 2006 12:15 PM
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Subject: Re: [FW-1] Solaris 9 BGE card and NGX60
Hi Clive,
NG R55 is known to have some compatibility issues with BGE interface,
but NGX R60 is suppose to have resolved those issue. I have installed
NGX R60 with HFA3 on V240 server and it works fine.
Try adding the line "bge accept" in the file /etc/fw.boot/ifdev if it is
not already there.
Ramki
CCNA, CCSE-NGAI
Clive Luk wrote:
Dear List,
I am trying to do a new installation on my newly bought two SUN FIRE
V240.
Actually I want to setup as a cluster. However, When I installed NGX60 to
a
freshly built box, it seems that CP doesn't recognise the bge card.
Does anyone has the same problem? Is there anyway I can solve it.
Thanks in advance!
Cheers,
Clive
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================
|
