Firewall-1

[FW-1] AW: [FW-1] Dell PowerEdge 1950

Subject: [FW-1] AW: [FW-1] Dell PowerEdge 1950
From: Bernhard Weiser <bernhard.weiser AT NOLIM DOT IT>
To: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Date: Fri, 27 Oct 2006 15:50:32 +0200
Hello,

Great, this was the link I was searching for.

Regards
Bernhard Weiser 


-------------------------------------------
Dipl. - Inform. Bernhard Weiser
no limit Systemhaus GmbH
Kampenwandstr. 77c
83229 Aschau
Email: bernhard.weiser AT nolim DOT it
Email: bernhard.weiser AT nolim-it DOT com
Tel.: +49 (0) 8052 95139 14
FAX:  +49 (0) 8052 95139 11
Internet: http://www.nolim.it/ 
-------------------------------------------


-----Ursprüngliche Nachricht-----
Von: Mailing list for discussion of Firewall-1 [mailto:FW-1-MAILINGLIST AT 
AMADEUS.US.CHECKPOINT DOT COM] Im Auftrag von pkc_mls
Gesendet: Mittwoch, 25. Oktober 2006 08:35
An: FW-1-MAILINGLIST AT AMADEUS.US.CHECKPOINT DOT COM
Betreff: Re: [FW-1] Dell PowerEdge 1950

Miguel Angel Gutierrez a écrit :
> hello list,
> we were evaluating a dell 1950 in order to set up SPLAT in it, and 
> already took a look at the hardware compatibility page:
> http://www.checkpoint.com/products/supported_platforms/recommended/ngx
> /v
> er_r60/017.html
> but I didn't catch the hard drive specs so well... is it safe to say 
> that SPLAT can recognize, manage and work under this kind of hard
> drives:
> 341-3094  PERC 5/i, Integrated Controller Card 341-3030  146GB, SAS, 
> 3.5-inch 10K RPM Hard Drive
> 341-3084  Integrated SAS/SATA RAID 1 PERC 5/i Integrated
>
> I wouldn't like any nasty surprises during the setup hehehe...
>
> thank you for the comments... 
> --------------------------------------------------------
>
>   
for the perc5 you need specific media packs.
the supported hardware is described at this url :
http://www.checkpoint.com/products/supported_platforms/secureplatform.html

check your cds before the installation.
you can add a drive to splat during the installation only if you have an 
internal floppy (usb drives, usb floppies cannot be used to add a driver).

if you're looking for the driver, dell doesn't provide it for linux RHEL3.

you need to check at lsi site for the megaraid driver for linux.

the dell 1950 requirements are detailled here :
http://www.checkpoint.com/products/supported_platforms/recommended/ngx/ver_r60/017.html

you need to pay for the medias or to use a SR ticket to obtain the media kit if 
you don't have the cds.

hope this'll help.



        

        
                
___________________________________________________________________________
Yahoo! Mail réinvente le mail ! Découvrez le nouveau Yahoo! Mail et son 
interface révolutionnaire.
http://fr.mail.yahoo.com

=================================================
To set vacation, Out-Of-Office, or away messages, send an email to LISTSERV AT 
amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your subscription options, email 
fw-1-owner AT ts.checkpoint DOT com 
=================================================

=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to LISTSERV AT amadeus.us.checkpoint DOT com
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
fw-1-owner AT ts.checkpoint DOT com
=================================================

<Prev in Thread] Current Thread [Next in Thread>